In models of vehicle alarm with command again is possible (I advise to do so in the article on a new form of auto theft ), increase the volume of the siren in order to give us one more indication that the alarm was activado.O process to regulate volume is similar to the need for models with remote control, except that all steps are carried out through the button on the LED.
To increase or decrease the volume of the ringing bell is then necessary to enter the program, so it needs the PIN code supplied by the manufacturer or the code entered by you.
With the alarm off, open the driver's door and bonnet and connect the pin ignição.Digite code.Se all conditions are satisfied, the LED placed on the dashboard flashes and after about 3 so the system will display the table entry the buzzer of regulation through the car's direction indicators.
You are now on the table that lets you increase or decrease the volume of the siren (on or off when the alarm).
If you want to increase the volume, and repeatedly press the button in short blasts found in led.O volume will increase each toque.Caso the volume is too high, do not bother the neighbors because they do not press the button in long tones, once again the sound of the siren will reduce with each press of the button.
You can repeat this process as many times as you want until you find the desired sound level, so check that the volume of the siren is enough to listen to the call and turn off the alarm, but at the same time not annoying the neighbors, just turn off the ignition close the door and the hood to exit the system programming.
Again I advise you to use this function of the alarm cobra , new forms found by the friends of others (use of Jammers ) requires that all indications that the alarm is on when we leave the car are provided to us, using the same models CanBus .
Read also these articles:
 |  |
 |  |
 |  |
11 Comments on "Adjusting the volume of the alarm siren in the original command with"
I have installed a 3868 (with original command) in Golf4, the only problem is that increases (it is off) the volume of the siren and I can not download. Pressing the button nothing happens long tones, if you do so quickly remains at full volume. I'm doing something wrong? Thank you.
If you enter the program table should be able to decrease or increase the volume of sirene.O secret is in the ring, to decrease the volume touches should be extended, try again, I myself sometimes only the second is that consigo.Importante: The system must be on the program table if not, get the finger.
Cumps
Ok, I got it. The secret is the same rings. At first it is not noticeable reduction in the volume only after several note is that if the reduction. Thanks for the help.
Good afternoon,
I have a Clio Phase 2 and 3, newly equipped with an OEM alarm cobra renault 7887. I wonder how can I increase the volume of the siren as I think is too low. Thanks
To adjust the volume of the alarm siren in models with the original command just follow the instructions in the article.
The procedure is the same for both models PLIP or CanBus.
Again I refer you to access any program function is necessary that the alarm is properly installed or, hood switch installed and connected to signal door open.
Good.
recently bought a ford focus and came with a cobra alarm 3865, unfortunately not have the pin code and only once in qunado gun and that the car alarm. someone can give me as per code of origin or the source code and which manuakl and instruction?
greetings
Just follow the steps in the article on learning original commands .
Good.
If you install the alarm with the original command car to lose control of the panic function of the snake, right?
There is no way to put the button on the panic function bagajeira?
If you can respond to your email.
Regards,
RR
The panic function is controlled remotely by command and so I see no way to make a button.
Good afternoon.
I have a Renault Megane II Phase II alarm set by Renault. In the place where the alarm is written COBRA 97RA. Do not know if it is the correct name of the model but I would like to increase the volume of the same second as Renault does not (officially they) can not increase the volume due to rules "SOUND" But the alarm has a minimum volume, and I I would have tried to increase as it is written here and I can not. What else can I try?
Thank you very much
The volume of the siren does have limits because of the noise laws.
Comments