One of the most common problems is the loss of a command or even in some cases the loss of the two commands of the vehicle alarm, does occur in some cases where we bought a second hand car with a snake without alarm commands.
In either case it is always possible to program a new Cobra alarm command for your car.
If you have a command running and want to add a new procedure as follows:
1. Turn off the alarm system charges.
2. Open the driver's door and hood.
3. Turn on the ignition.
4. Press the button command to the vehicle's direction indicators flash once.
5. Enter your PIN code.
6. The direction indicators will flash twice and the LED is fixed, indicating that came in the way of self learning.
7. Press the two buttons on the new command until the LED turns off command.
8 Stop push buttons and verify that the LED is fixed.
9. Press the button command, verify that the LED flashes and the command that is that the led on the dashboard goes off for 1 s, direction indicators should also flash to confirm that the new command was added and stored in the system.
10. Repeat steps 7-8-9 for all the commands you want to add to your alarm system, these steps should be taken to the command previously memorized.
11. If after 30 seconds perform any operation system automatically exits the self learning mode.
12. To exit the self-learning at any time simply turn off the ignition.
Setting new commands without having any active command.
If you purchased a car and not have any active command proceed as the following:
A. Turn off the alarm (the fuse or disconnecting the plug from the center)
B. Open the driver's door and hood.
C. Turn the iginição.
D. Reconnect the power alarm charges.
E. Enter the PIN code of your alarm.
F. The system will confirm the correct code and the LED will light for 2 s.
G. After only five LED will flash indicating that the alarm system went into learning mode.
H. Repeat steps 7-8-9 explained before for all the commands you want to add.
Note: when programming a new alarm command collects all the previous commands will be inoperative. Can add a maximum of four new commands.
Read also these articles:
 |  |
 |  |
 |  |
66 Comments on "How to program a new command alarm cobra"
where do I send a command alarm charges
Depends on the model of alarm charges, if a recent model, you can order the representative of Portugal in a cobra alarm virgin command and follow the programming instructions above.
If the model is old, I mean the command rectangular buttons with green or yellow, will indicate the representative with the serial numbers that are within the command that has in order to be sent to you a command already programmed for your alarm.
I bought a car, and I have the pin alarm cobra, how can I get? thank José Luis
What type of snake you have installed alarm?
hello, I have a snake in my car and not to give this one beep the doors close and open as I enable it?
It is a simple process to make sure all connections are correct the alarm.
You can read the article that explains how to adjust the volume of the siren and follow the steps.
If you need further assistance please feel free to post a comment.
Thanks for visiting
Good!
Have you ever noticed that when an alarm is activated the same snake makes a beep, I think the sound (I am not referring to the volume) is different given that beeper alarm for alarm and is not a program that can do the same, I am sure ?
Thanks
The beep is the same for all alarms charges, the difference in tone or volume may vary due to the mounting position of the siren or vehicle type, some engine compartments are more soundproof than others.
If you want to read the article on how to adjust the volume of the siren.
Cumps
Good day
I lost my alarm two commands Cobra like to know where I can purchase new commands and what they cost.
Commands other alarms Cobra "used" also give to reprogram?
The new commands are on average 40 Euros plus VAT and can be purchased at any installer.
Cobra Any command can be reprogrammed for your alarm as described in the article.
Dear Friends
I wonder where I can here in the port area to send commands to a two alarm Cobra "4B5801STB" (I think this is the reference) for a used car I bought, I do not know the code but I have a small key to "ON / OFF "said the alarm, which has five characters consist of four digits preceded by a letter (?) I think (it's a bit off, is it?)
The references that mention I do not say nothing (do not know everything), but if you want to be equal to the commands of the picture , you need to have the pin code of the alarm in order to program the new commands .
If you do not have the pin code of the need to replace the alarm control panel with a new one that comes with two commands and their code.
Cumps
Viva ...
I bought a car in two. Nd hand with a cobra alarm function. Why not activate the first time and decided to open the command. I withdrew and went back to the battery. The center receives no orders from the command ... that is, have the car with the alarm on and do not know how to turn it off.
NOTE: I have tried the technique of the two buttons simultaneously ... to no avail.
I do not know the PIN ... and I have qq switch to turn off the ECU,,, alias I was told on the stand that this model had no such system ...
I would appreciate one (or more) tip.
Thanks
Good,
If the command is the same as the picture you probably need to change the battery and set the command after the replacement.
Check that the LED has a small button, if you can e-mail the pin code at the factory so you can turn off the alarm without a command.
Cumps
Where can I make a new command for my car and the brand Cobra
You can ask any installer that works with the brand of snake alarms.
I'm trying to create a list of installers nationally but still I could not make it happen.
Cumps
I have a problem is the following: I intend to schedule a new command, and follow all the steps that are here transcritos.O happens that when it reaches the point G. (After only 5 LED will flash indicating that the alarm system went in learning mode.) LED does not light up.
What could be missing? .. Because the pin code is correct.
Thanks
Bruno Afonso
For every step function is necessary for all alarm connections are made, if eg. the connection of the bonnet or door alarm was not made does not go into programming and so nothing works.
Check all these links.
I proceeded to change a battery and now I have certainly seen to reprogram the alarm that the command does not perform any function
I bought the car second hand and which know the pincode and there is no on off switch type
must be a type of alarm charges less recent
Already tried to reset the alarm says when changing the battery but the function does not correspond to the LED mentioned I should do
The procedure to be performed when the command changes the cell is described in the article, requires no pin code to perform any of reset comando.Apenas need to be with the car, press the two buttons at the same time and when the LED stops flashing, Release the buttons and press the button twice more.
Good, recently bought a cobra alarm of a car alarm was going to scrap it only has a command and is a 7905. To schedule a new command is required to pin cod alarm? It's not that I have!
Where can I get?
Thanks
Without Pin Code Alarm is not really possible to program a new command.
For the model of alarm that said there is no possibility of creating a new code for this station (at least until very recently), it is necessary to deliver the old center is in place and provided a new plant with two new commands, I have this the exact value.
If a command is running and do not actually need another, preserve the good, replace the battery and if you are in poor condition, the box can also be replaced.
I hope that helped
Cumps
good;
I have a car 2nd hand and I td installation charges with reference 5897 and have the command td advantage of the brand of my car, give Keria ask for a command, but must be the same command that such a K Custom be gray? or kk command virgin to reprogram the?
the price of 40 € is a command or a pair?
My cumpuz
I can not understand well what you want, but if the command that has failed is the original car, you have to ask for the brand.
The value of 40 € is the average value for a command of the snake.
Good evening, I bought a car recently that had an alarm fitted, but that brings no command, the alarm is a 7905 Cobra - 4B7905B1D at least is what is written in the alarm, and I ask is if there is way Buy a command and calibrates it with the same? If so, where in the Lisbon area?
Good night
It has the Pin code of the alarm?
Gostavade know if the interiors of the commands ha ha sale
Commands are sold complete with outer case or just the outer plastic box.
Good night
to reprogram an alarm system is required plip module programming Morpheus?
Is it expensive?
if you can help with these questions thanks
a hug
The Morpheus software is only required for alarms CanBus type 4918, 4415 and are typically pre-programmed for a particular model before instalar.Qual is the vehicle you are or want to install?
For 3868 models called plip or G368 is not necessary, just follow the steps here described.
Cumps
Good evening, I thank their availability. The alarm is a g368 and I intend to withdraw from an Alfa Romeo 156 and ride on a opel corsa. How should I proceed then to recognize that the "signs" of it?
thanks
greetings
Just follow the steps to program alarm plip after being correctas.Atenção the connections that can be different from the old vehicle.
Cumps
Good morning everyone.
I bought a car for a short time with only one command. I know nothing about the alarm, since I bought the car less than a month. This command was walking in my purse and what happened is that I arrived at the foot of the car and can no longer dasarmar the alarm. cell but has not disarmed and whenever I try to enter it the alarm is activated. The only thing I have the same alarm is the only command that was already scheduled.
See this article
http://alarmescobra.com/2008/08/alarmes-cobra-substituir-a-pilha-e-programar-o-comando/
Thanks
Did it work?
Hello Friends!
Can someone Please make me to inform me if there is a possibility of sending a duplicate command to run the Cobra alarm?
Is that my commands are getting worn and need to get a new one without replacing the alarm.
I thank pawned the answer to my question.
Regards,
Armando Monteiro
Porto - Portugal
Hello I bought an Opel Corsa in 2nd hand, which had an alarm snake (the command has two Butoh green), the previous owner sent off the alarm because it was too sensitive and too easily triggered.
A week ago I went to an electrician to reactivate the alarm, but was not being possible, the electrician tested the command on a device to see if it worked, and he said the command was not working. He told me that without the command was not possible to reactivate the alarm.
So my question is: need to buy a new alarm or just buy me a new command?
(When I bought the car I was not given the alarm pin)
Just buy a new command set.
@ Admin
If you have a command running and want to add a new procedure as follows:
after this procedure is completed, cancels the other command or the two are working.
hello I have a command that is not snake can I use the commands in another type of snake alarm? thanks
Not that I know at least the alarms do not allow charges to add any command.
I speak of the universal commands that are then programmed etc.Agora if the alarm is allow other commands not know.
You have to program the two commands.
Good afternoon,
I was robbed last week and got me the car keys which in turn was also at the command of the alarm. My question is I have an alternate command, will be giving to "reprogram" (not sure if is the correct term) I have this command so that the other leading be deactivated and so I'm not likely to turn me off the alarm?
If you set a new command all others are disabled, with only one command can do the same for the programming process this command to reset erases the old programming.
However I advise to always have two commands to work, avoids many problems if a crash.
Good Morning
Sorry to be putting this question here, but my alarm and so the snake has the 7918 wireless antenna switched on, and I wonder where and what I do I call? thanks
I bought a cobra command the alarm function is operational but the function lock and unlock doors is not working. What can I do to put in place??
If the alarm on and off with the command might be malfunction in the control panel or links (fuses, contacts, timing of closing).
I would like to buy control of my car, the model cb 200, cb 300
I live within sao paulo, sp meridian, Brazil CEP 15625-000
I can not find here .. hope to answer as fast as possible ..
I have a 7777 cobra alarm in my car. Long rubber rods were dried in command and ordered two new cases. One of Confucianism commands normally, but the other, although the light on, crashed. How should I proceed?
Thanks
MAR
Just do the reset command as described herein.
Good Night.
G198 I have an alarm, but I see neither the manual nor is active on the Internet as the "detector of the car" (Car Finder).
Can you tell me where to find these instructions?
Thank you.
To activate the Car Finder just press the command button, this function is active 25 seconds after turning on the alarm.
Good morning,
Some time ago I needed to do a reset to the PIN of my control panel and got through a procedure that taught me here.
It was ok because I can turn the alarm off with the command and entering the PIN again.
Now I finally get a new command but I can not add to the core.
I follow the procedure here but I get to step 6. After step 5 (enter the PIN in charge of the dashboard) the indicators do not flash and the LED is not fixed way of indicating the apredizagem.
I'm doing something wrong? The centerpiece is a 3995.
cumps,
LC
The bonnet switch is on?
Good night
That's right!
To test whether it was open the hood with the alarm on ...
Nothing ... The alarm did not go off ... I dismantled the switch and found that one of the chips was loose. For the system when the hood was closed!
I managed to set the!
Obrigadíssimo!
Just out of curiosity to program the new command the old crashed. I had to re-enter the learning mode and to program two in one session.
Again thanks!
Yours sincerely,
Luis Catullus
Good evening, I have a cobra alarm and I can not insert the pin in order to able to complete the setup process of the new command.
The LED has a button around it ... I tried to press as it should be ... but no sign of alarm ... what will?
Regards,
He had to run another command?
The bonnet switch is on?
good. someone out there has a 5575 cobra command to test the power of my car? mine is broken but I can see the shunts programação.assim-cuts could then copy a. already my thanks.
someone has th 5575 where a command so you can test snake in my car? already my thanks. jorge
good
I have a cobra alarm, but it works with the command key, and I have an alternate command, wanted to buy a program command but do not know, I've had to do the tutorial but do not know anything about that, got the card and PIN to the SN, some help ?
If your alarm works with the original command of the vehicle has to buy the brand.
but when I bought the car had no alarm, sent by the booth and gave me this as well, was already more than one year, the stand has closed
The commands of the new generation are easy to program as described in the article, just take the pin code of the alarm.
I got the pin and serial No.
You can order the command already programmed?
The 7777 commands are supplied blank and must be programmed into the car.
Or alternatively, you have to disassemble the center so you can plan on a bench.
4 Pingback & Trackback On This Post
Comments