The command 's use charges cell s as the image shows, batteries are the type that may be in CR32 representative of the alarm, a distributor or store any type watchmaker or photographs.
By opening your command to verify the charges mounting position for the cell polarity must be maintained, otherwise your command will never work.
If you do not remember the last post position to consult on the control box and click on the photo charges in order to view the correct mounting position of the stack.
After returning to set up your command to check its correct functioning, sometimes this is where the difficulties begin, it happens that the controls stop working, and the need to program the command, this is not necessary to use the services of technical or charges even a reseller.
To schedule your command snake just follow the procedures that I describe here:
1. Acerquem is the vehicle to which it is associated with your alarm command.
2. Press the two buttons simultaneously control the alarm, should command the led keeps flashing.
3. Keep both buttons pressed until the LED of the delete command, release the buttons of the command and verify that the LED is fixed.
4. Press the button two times higher and the car alarm will trigger.
5. Repeat the process if does not work, because sometimes some of the procedures was not conducted properly and the alarm did not recognize the command.
And voila, after the command is damaged and not have to think about buying a new, I know some of you might be thinking that after all is so simple and the command in a drawer waiting for an opportunity to return to work.
I know from experience that this happens to many, I got to program commands to the very charges that were saved and that only after losing the second is the re-run.
I hope this post about changing batteries and reprogramming of the command that will facilitate the users will have this difficulty and that here they can access the correct procedures for this simple operation.
See video and put the alarm command back in operation.
If you liked this article share it with your friends on Twitter or Facebook. I appreciate that. 
Read also these articles:
 |  |
 |  |
 |  |
71 Responses to "Replacing the battery and program the command"
Dear friend I give you my congratulations for the information and solutions presented.
He liked to ask for help because of my alarm, I ended up going to replace the batteries as close to a watchmaker and now my command it does not work, send signal but does not open or close the car and not the alarm works. What should I do? However I tried to get in many stores alarms area of Vila Real, etc., or make a copy if possible and nobody solves the problem. I really need the command and I have done everything to fix and nothing. I leave my email here (removed) if I want to help or even a state store that I solve the problem.
I really appreciate your help in solving this problem.
Sincerely: Jose Rodrigues
Thanks for the comment.
If the command is just follow the signs round the post, replace the batteries and program the command.
Sometimes it works at first, make sure the light turns on command and repeat the process.
hello, good afternoon Mr. Jose Rodrigues.
Spend a store network chaviarte and there you will find for sure, I know a friend of mine bought a store in Port la dolce vita. greetings
It works?
As I said earlier in 99% of cases it is not necessary to buy a new command, just reprogram it when replacing the batteries.
hello and how it reprograms qo??
ja agr and buying a new encoding as qso?
greetings
To reschedule or do a reset command crashed when replacing the battery just follow the instructions of the post above.
To synchronize a new command to wait for their post (it's in the pipeline).
hello, good morning. ms s so I have a command like and buy another program??
thank you
Cump
I thyltin a new alarm ... it came with a card with a number ... these numbers are used to disable or enable the alarm is not it? But what is the procedure?
Thanks for visiting Nelio.
If the alarm is recent addition to the card with the deactivation code, you also should have been delivered to the user manual which explains the whole process.
To be exact I need to know the type of alarm, because if it is a new model the procedure differs from earlier models in which the code was inserted through the ignition switch, new ones are led through.
Say which model.
Hola, thanks for the tip. He was hampered with this hassle of re-programming of the alarm and was beautifully resolved. I am grateful! Adriana
hello ... I think the model is the G100 at least that's what is written in the manual ... but they gave me the manual I've been reading but can not find what you wanted ... the alarm has the modules for the glasses too ... alarm has led you said like you with the red light and a button, I know that one has to press the button for the alarm but not dessativar'm really ... nothing to see how the card is written the PIN CODE 9736
Another thing ... esprementei to take out the battery and return to the command to see if a program was needed but was not ... Do these new alarms no longer need?
To disable the alarm in case of failure of command clicking (in your case) 9 times the button the LED, the LED blinks once, click 7 times the LED blinks once, clicks 3 times, the LED flashes back to a time and finally 6 times and the alarm off.
To try to turn the alarm off command and through this process.
Tell if it worked.
I did teach here as to regulate the volume, but not led, I followed all the pasos and nothing.
Another thing've seen some snake alarms each time you turn on or off the alarm he makes a whistle or two depending on whether to disable this or not but my call is this ... how can I do? 've read the manual several times but does not explain how.
Embrace Nelio
The process is the same that you use to adjust the volume.
Often it is not possible to enter the programming mode due to bad connection of the alarm.
The switch wire doors and hood must be connected.
Thanks to leave comments on their articles, it becomes easier for everyone.
WHERE TO BUY CHEAP AN ALARM COBRA? ADVISES which model?
Thank you for giving me recognition capabilities on the subject to advise you, however I can not do without indicating which model of vehicle in which you want to install alarm charges.
I will be happy to help if I indicate the make, model and year of vehicle.
Good friend.
I hereby ask for your help. My car (Opel Corsa) left the factory with a Cobra 5801 alarm, but as ocarro bought second-hand commands did not exist. As such I wonder if it is possible to control the alarm with universal commands and how to program the commands would be possible for the alarm because I have absolutely no information about the alarm unless the reference and model.
Greetings and thank you.
Tiago Teixeira.
Dear James
You can ask the representative to encoding new commands , it has no reference code of the alarm will have to disassemble the plant and sent to technical services.
Good,
I have a problem with my alarm, I was gone 10 days and when I turn flashes 5 times (instead of two) when blinks 4 instead of 1. The clock, interior light and radio do not work. What could it be?
Good,
I think the reason the clock, interior light and radio do not work due to a blown fuse in resolving this probably solves the alarme.Pode be related to the inner light or the car battery ran out.
Check fuses and test the alarm .
Check back often if you need help.
Cumps
I just want to thank you very much for the information provided here! He saved me from having to take the car to beep me for a workshop to unmount the alarm and send commands over the keys to Lisbon and etc etc..!
So simple!
Great even!
Thank you once again!
No more and best regards
Cheers
Thanks for visiting and comment.
It's always nice to know that our work has helped someone.
Please check back often.
Cumps
good night!
recently bought an alarm from the snake, the model G100 or G300'm not sure I know things have pin code, the siren is not self-powered and has commands that happens ... a round of them ran out of battery and was mto time without the battery inserted, deprogrammed now, it happens that I have tried to follow the steps listed on the site, open the bonnet, door etc. .. but it does not set or the LED will flash the indicators or ... do nothing ... that is, it seems that there is connectivity between the command car and ..
greetings
Carlos Carvalho
Good night
For models that refers simply press the button for some time on the car.
Cumps
Good night
I mod.5340 cobra alarm after replacing the batteries no longer work.
Thanks. a tip for the program.
Thanks
Good afternoon,
I referred earlier to the commands, with two square buttons, right?
If so check the battery contacts, clean the area of the buttons with alcohol and retest, this kind of commands do not need programming.
Cumps.
au ok.os these commands are so many attempts in this genre is acavarao bought a ruin in Ebey and not thanked you for the works over the tip if possible ob
These commands have the same type of programming of the new, ask for a copy is required no who is a sticker inside the command, if there is no need to disassemble the plant and send it to the technical services to new commands.
I do not think any other way, remove the panel and send it together with this command, which can be reprogrammed.
Cumps
I have a Cobra 1994 alarm ... the alarm works connected with the key but can not set up a command ... How do you do?
Your alarm still has two commands with rectangular green buttons?
If so these commands do not have programming, open box, replace the battery if it is unloaded and wipe with alcohol (without exaggeration) the area where the printed circuit push buttons.
Cumps
Good.
I need to replace the battery command used the Cobra 7777. Initially follow the instructions in the manual but the command just stopped working (LED lights, but the command center of the vehicle does not respond). Having searched the net found your blog on the subject and followed your directions but still the problem of non-functioning the sistema.Aparentemente not get past the second phase - corresponding to the second paragraph of his text on the programming of the command - which led the light of the command remains fixed and does not blink when the simultaneous action of the keys.
Thank you for your attention.
Cumps,
John Gomes
Good,
You must perform the procedures with the car, pressing both buttons simultaneously for some time (delay) to change state and then press the large button command.
If the LED lights of the command, the procedure is the descrito.Tente back again.
Greetings
Good morning,
In a few days here that the command does not work correctly. When you press the button to open the door the led is fixed for a few seconds and does not open the car, then flashes a few times and off.
When I try again or open and the car runs fine and the problem repeats itself.
What is the problem, lack of battery?!
It is most likely.
Replace battery and reprogram command.
I changed the battery in the alarm command Sicurtronic (only with a command button) and do not know how to reprogram it. Since I think the manufacturer is the same Bosch might get help.
thanks
The following model relates to what is equal to the Cobra with a slightly different design and therefore the procedures are the same.
The models with only one button Sicurtronic were represented by Bosch in Portugal until a few years now disappeared from the market altogether, do not know if I have something saved to help with that, but on Monday I can stand here and look.
Cumps
good night ... I looked for a solution for ca a situation that does not taste great, do not know if has a solution ... I bought a used car, peugeot 106xsi 95, 7915 brought a snake alarm works ... usually ok, but not like the lock ... .. engine type, turn off the car, after 20 to 30 seconds longer handle, locks the injection pump ... ... to be that of taking this so??
lengths and thank you ...
Thanks for the help Post 27 February. Alarm Sicurtronic.
Thanks
Good night
The command has no relation to programming, I could not today, but I'll try to talk to a company that made the technical assistance of Bosch / sicurtronic, it may still be able to repair this command / control panel.
Cumps
Thank you for your attention
Cumps
Good night
Today I spoke with who was assisting sicutronic alarm, as I said this command has no programming and no longer exists any material for repair, he had bought the entire stock of various repair and sold it to a few months.
If the command only stopped working after changing the battery is probably not broken, I know that maybe it did but make sure the battery is really good (as happened to be new and no load), it is in the correct, clean the contacts, check the welds of the board and try to work without the box.
I think that if one of these things is nothing there to do, I regret not being able to help more.
Cumps
Good afternoon
I am asking you please if possible give me a little help on a problem that came to me in alarm charges.
When I turn on the lede does not flash, is fixed, and you hear a little whistle from the area of the engine (when connecting the MEMS and appears briefly). I suppose the alarm is self-powered
Sound is weak and this lack of power in the battery of the same alarm ...
Really? He asked the favor of the subject who knows if I confirmed.
Advance grateful for the attention.
ASRosa
Good afternoon,
I do not think the problem is this, the alarm turns on and shuts the door?
What is the type of alarm, car?
Cumps
Good night
The manual alarm does not indicate clearly what it is. There's a list from 7901 to 7919. I have the car to see if I find the model. The 7777 remote is a little think what it says.
However, the command opens and closes doors, but closing it when the lights two times the indicators and does not as usual, ie the LED was blinking but stays fixed and there is the acoustic signal to connect but still.
Thanks anyway.
Greetings
ASRosa
Check the bonnet switch or some of the doors is not closing well.
Cumps
This topic has saved me a trip to a workshop and expense that would certainly not small. Thank you.
Good ... I have a Sicurtronic alarm installed in my car and just have a command function.
Anyone aware of any representative or where I can send more commands to do?
Thank you and all cumps
Depends on the model of the command, so the oldest commands no longer exist but for the latest models can be used in the 7777 Cobra.
If sending image can answer with more certainty.
Cumps
admin ... like sending the picture?
I sent mail
Hello, I have a corsa b with an alarm sicurtronic but do not know what model. I wonder you download the volume of touch when he locks the doors and open, and has a module for the rear of the snake, I think with a model number something like 19?.
I can display the alarm, this one for sale on the net:
I apologize to Mr.. but as of this announcement do not know for photos, and doubt like to see this resolved.
If anyone can help I would appreciate, since they do not have the manual, since you bought the car 2nd hand.
Gonçalo Surra
Try as it is in http://alarmescobra.com/2008/12/regular-volume/
Good night, someone can tell me the model Kual ka renault espace III behind?
K I bought a second hand ~ but not yet managed to figure out the model of Kual alarme.Aparentemente the alarm so to say only this to open and close the doors, because I see no sensors, but not the fuse box is a module with the number 1046, the command has enkuanto 0678, some of these numbers is the model?
Thanks
I have a good focus for 2000 sw replace the battery but now the command does not close or open the doors ... thanking ajuda.obrigado
Article battery replacement and program command has the answer.
Cumps
Good.
I have an anti-carjacking charges alarm that turns on with the key of the car and also comes with a kind of card.
Only now the alarm call and that's fine, but when I disconnect it does not recognize the card and the alarm rings, I can only turn off the pin.
Does the card need to stack? The manual says nothing about the card.
Thank you for your attention.
Check the battery of the card in the 118 page manual comes with an image as a battery.
Good.
I have a snake in my car alarm, but do not know the model, the command is of the old with the two green buttons (the ref. AML5557 Ordering is), and needed a new one, since it is a party and the other does not work . The problem is that for the order numbers in the command are not very noticeable and did not want to give these numbers because I can fool me and then the command does not work. So my doubt is where the numbers in the main module and how many digits it has? The numbers of level modules do not?
Thanks
Hello good evening!
hj changed the battery in my command snake, which is the round black with two gray buttons the same as it appears in this video post;
I tried to do the procedures themselves but for qd push both buttons at the same time the LED does not blink command semrpe is fixed and not pushing it off ... if you can help me?
thanks
There is no other procedure or trick.
Remove the battery and reinsert and try again.
Thanks, already got! I had to repeat the procedures again and again ... but I did!
thanks for the tips!
I just want to thank you for the information siponibilizada this blog. Follow the instructions and reemparelhei the module with the car alarm after battery replacement in less than a minute!
Thanks
Viva ... Good afternoon I bought a car 2nd hand that includes an alarm cobra 3020 have the two commands put two new batteries 12v one in command, but the alarm still does not work when I turn the key to the siren so the beep crush and nothing more and has also confirmed the entry of 12V input to the ECU. I do not know if it's one of the commands as they are not led to see that they are operating. The command buttons are black with two green and red LED inside the car not the sign of the will vida.Desculpem. Thank you for your attention ... now Cumps
Usually the problem with this type of command is in contact with the circuit of the rubber erasers impresso.As begin to crumble and not make good contact.
In addition to checking the current input should also check the grounding.
Good day
I bought a Renault Laguna 2003. One of the commands (the 2 buttons) was damaged. A guy friend opened it and welded it. Now the buttons work, the led, but it seems deprogrammed. Is it possible to give me a hand?
Thank you and cumps
Has already made a reset command?
Good night
Thanks for the reply.
How is this reset renault card?
Cumps
Sorry to insist, but it is not a command snake.
is a card / key ignition of a renault laguna.
thanks
The programming of the original commands of most vehicles has to be done on the machine's representative.
Thanks for the info!
already saved me a trip to an official agent or someone who can install alarm the snake!
Comments